carburizing and quenching是什么意思，carburizing and quenching的意思翻译、用法、同义词、例句

渗碳淬火

Applications : widely used for the carburizing and quenching of gears, bearings, shafts and other mechanical parts.

用途： 广泛适用于齿轮、轴承、轴类零件及其它机械零件的渗碳、淬火热处理工艺。

The distortion of gears and gear shafts resulting from carburizing and quenching is difficult to avoid in production, and the reduction in distortion is a difficult problem in technique.

在生产中，齿轮和齿轮轴的渗碳和淬火畸变是难以避免的，减小其畸变量是一个技术难题。

Employing abrasive machining for the form of the gear and intellective-control carburizing and quenching technology for the surface, the gear is with high intensity, strong tenacity and wearability.

齿轮齿形采用磨齿加工，齿面采用智能控制渗碳淬火技术，齿轮的强度高、韧性和耐磨性好。

The wear resistance of the laser alloyed layers was 5.7 higher than the nitrogen treatment steels if the upper sample is carburizing and quenching steel rings.

上试样为渗碳淬火钢环时，激光合金化层耐磨性是钢氮化处理试块的5 .7倍。

Purpose: Widely used for the carburizing and quenching of gears, bearings, shafts and other mechanical parts.

用途： 广泛适用于齿轮、轴承、轴类零件及其它机械零件的渗碳、淬火热处理工艺。

The distortion of gears will take place during carburizing and quenching and, as a result, reduce precision of the gears and increase noise, or will even cause unbalanced load-bearing of the gears.

齿轮在渗碳淬火中会产生变形，直接影响齿轮的精度，增大噪音，甚至造成偏载。

Due to the cleaning temperature is about 200℃, a low tempering could be done in the same process for these which need to be tempered at low temperature after carburizing and quenching.

克服了浸泡、喷淋清洗方式清洗效果差的缺陷。而且清洗温度较高，对于渗碳淬火后需进行低温回火的零件可实现清洗、回火一并完成，省略了回火工序，节省了能源，体现了节能和环保意识。

The surface high speed steel and its high propeties are obtained by surface alloying with W Mo, carburizing, quenching and tempering.

采用双层辉光离子渗金属技术，首先在低碳钢表面渗入合金元素钨、钼；

The application, influence factors and process control of four kinds of heat treatment methods including tempering, carburizing, nitriding and induction quenching are analyzed.

对齿轮的调质、渗碳淬火、渗氮及感应淬火四大热处理工艺的应用范围、影响因素及工艺控制要点进行了分析。

The series is ion equipment and vacuum carburizing quenching equipment portfolio Series vacuum heat treatment equipment , Both have its advantages.

该系列设备是离子渗碳和真空淬火设备组合，具有其两方面的优点。

This paper deals with the carburizing process, microstructure, mechanical properties and quenching distortion of the air cooling low carbon bainitic steel.

对低碳贝氏体钢的渗碳工艺、显微组织、力学性能、淬火变形进行了研究。

The paint film can peel off automatically from the surface in quenching procedure after carburizing, and it does not affect the quenching effects.

工件渗碳后直接淬火，涂料壳膜可从工件表面上自行脱落，不影响淬火效果。

Use:For carburizing, quenching, car-bontriding and bright quenching of the various smail machine parts.

用途：各种小型机械零件的气体渗碳、淬火、碳氮共渗和光洁淬火用。

Before 1949, Beijing has heat treatment furnace, salt dissolved by thermocouples means furnace, quenching and tempering, parts of annealing, normalizing, quenching and tempering, carburizing and etc.

热处理1949年前，北京已采用电炉、盐溶炉、热电偶等手段进行零件退火、回火、淬火、正火、调质、渗碳等热处理。

Direct quenching after carburizing can meet technical requirement in order to save working time and cost.

为节省工时和成本，渗碳后采用保护性气氛加热直接淬火可以达到技术要求。

The effects of direct-quenching heat-treatment through gas carburizing on the spot contact fatigue life of crosspiece and bowl was mainly stu***d.

采用气体渗碳直接淬火热处理工艺对力车轴档、轴碗进行接触疲劳寿命的影响试验。

The results showed that, by certain cyclic quenching process, coarse grain of high temperature ion-carburizing can be fined effectively and its mechanical property can be improved.

结果发现，经一定的循环处理后，可以有效地细化经高温离子渗碳后的粗大晶粒，并能改善机械性能。

Based on carburizing quench test of synthetic quenching medium, this paper analyzes the heat treatment process of 20Cr and discusses the applicability of synthetic quenching medium.

针对钻井用吊钳牙板使用时易崩碎、不耐磨的特点，分析了原因，改进了牙板渗碳淬火的热处理工艺。

L. resulted from carburizing in the course of oil quenching 121 vacuum. After the causes of formation of W. L. and M. L. are discussed in detail, three necessary conditions for form…

本文对白亮层、溶化层形成原因进行了比较深入的分析探讨提出了产生白亮层必须同时具备的三个条件。